Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Rhawnhurst Homeowners
Most chimney problems in Rhawnhurst start small and quiet: a hairline crack in the mortar crown, a few flakes of brick on the walk, a rusty damper that sticks when you try to open it. Left alone through a freeze-and-thaw winter, those small problems become water inside the flue, and water is what turns a repointing job into a rebuild. Our technicians have up to 15 years of experience reading exactly that kind of damage, and we do chimney work only, so we know what we’re looking at. We diagnose before we quote and show you the camera evidence of what we find. Call (866) 861-1187. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday, and same-day appointments are often available.
What Our Chimney Repair Service Includes
Chimney repair in Rhawnhurst covers everything from a tube of mortar to a full stack rebuild, and the right answer depends on how deep the damage runs. Here’s what each part of the job actually involves.
Mortar Repointing
Repointing means grinding out the old, crumbling mortar between bricks and packing in fresh mortar that bonds properly to the masonry. You need it when the joints have receded or turned to powder, which lets water sit against the brick face instead of running off. We match the mortar mix to the brick so the repair doesn’t trap moisture or look patched, and we work the full joint depth rather than smearing a skim coat over the surface.

Spalling Brick Repair
Spalling is when the face of a brick pops off in flakes or chunks, usually after water gets in and freezes behind it. Once a brick spalls, it keeps absorbing water faster, so the damage spreads to its neighbors year after year. We cut out the failed bricks and replace them with matching units set in the correct mortar, then treat the surrounding masonry so the same spot doesn’t fail again next winter.

Chimney Waterproofing
Waterproofing is a breathable sealer applied to the exterior masonry that pushes rain off the brick while still letting trapped vapor escape. It’s the right call for a chimney with sound bricks but a history of damp patches, efflorescence, or rust stains on the firebox. We apply it after any repointing or brick replacement is finished, never over failing mortar, because sealing a damaged joint just holds the water in.

Flashing Repair
Flashing is the metal where the chimney meets the roof, and it’s the most common source of leaks people blame on the flue. When the flashing pulls away, rusts through, or was never stepped into the shingles correctly, water runs down the chimney chase and shows up as a ceiling stain far from the fireplace. We rework the flashing and counterflashing so the joint sheds water the way it should.
Chimney Rebuilding
Rebuilding is for chimneys where the damage runs past the surface: crumbling brick through the full thickness, a stack that’s leaning, or a chase that’s been rebuilt badly before. We take the chimney down to solid masonry and rebuild it, keeping the flue geometry correct so the fireplace still drafts. This is structural work, and it’s the kind of job sweep-only companies turn away from.
Tuckpointing
Tuckpointing is the finer version of repointing, where a finished mortar line is worked into the joint for a cleaner, more uniform look on a visible chimney. It’s often chosen on chimneys facing the street or on older Rhawnhurst homes where the brickwork is part of the character of the house. We use it where appearance matters as much as weather-tightness, and we keep the mortar color consistent across the whole face.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Repair
We install and work with DuraFlex and HeatShield products, and both come up often when a repair turns out to need more than masonry work. DuraFlex stainless liner systems are what we reach for when a clay flue has cracked and needs a new path for the smoke, and we know how those liners seat, insulate, and connect at the top plate. HeatShield’s ceramic resurfacing system is the other side of the same conversation: it lets us repair a deteriorated flue from the inside without tearing the chimney down, which is a real option for homeowners who’ve been told they need a full rebuild.
We also work with Gelco and Olympia Chimney products for caps, dampers, and related components that finish a repair properly, and we choose the material to fit the flue rather than the other way around. Whether your chimney already has one of these systems or you’re starting from bare clay tile, we can help, and we’ll tell you plainly which repair path makes sense for your chimney and which one is a waste of money.
Signs You Need Chimney Repair Right Now
Some chimney damage is obvious from the ground. Some of it you can only see with a camera. These are the signs worth acting on:
- Crumbling or missing mortar joints. If you can pick mortar out of the joints with a screwdriver, the chimney is losing its weather skin. That lets water into the brick, and the next hard freeze can push the face right off.
- Flaking brick or brick dust on the roof or walkway. Spalling brick sheds material as it fails, so flakes at the base of the chimney mean the masonry above is already breaking down. Catch it early and it’s a brick replacement job, not a rebuild.
- Water stains on the ceiling or chimney chase. Brown rings or damp patches near the chimney usually point to flashing or crown trouble, not the flue itself. Finding the source early is what keeps a flashing repair from turning into rotted framing.
- A white, chalky powder on the exterior brick. That’s efflorescence, and it means moisture is moving through the masonry and drying on the surface. It’s a symptom worth diagnosing rather than scrubbing off.
- A strong smoke smell or a damper that won’t seal. Smoke backing into the room or a damper that sticks open points to a flue or firebox problem that needs a proper inspection. It’s also a draft and safety issue, not just an annoyance.
Our Chimney Repair Process – Step by Step
- 1
Inspection and camera scan. We start with a visual check of the exterior masonry, crown, flashing, and cap, then run a camera down the flue to see the liner condition from the inside. You see the same footage we do, so nothing gets recommended that you can’t verify yourself.
- 2
Written diagnosis and options. We put the findings in writing and lay out the repair options in plain terms, from a small repointing job to a liner repair with HeatShield or a rebuild. If part of the work can safely wait a season, we say so.
- 3
Flat-price quote agreed before booking. Once you’ve picked a path, you get a flat price for the job. That number is what you pay, and the written estimate sets the final price.
- 4
The repair itself. Repointing, brick replacement, flashing, waterproofing, or a liner installation all happen with the right materials for the masonry and the flue. We keep the work area clean and protect the roof and landscaping as we go.
- 5
Final check and photo report. We test the draft, confirm the repair holds, and send you a photo report of the finished work along with anything to watch next season. The whole job is documented so you know exactly what was done.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Repair Cost in Rhawnhurst?
A typical mortar repointing job in Rhawnhurst runs $350 to $900 depending on how much of the stack needs work, and a flashing repair usually lands in the $250 to $600 range. Waterproofing is often in the $300 to $700 range for a standard chimney, while spalling brick repair adds cost per brick replaced, and a full rebuild is a larger project priced per job after inspection. A HeatShield flue resurfacing or a DuraFlex liner install to fix a cracked flue typically runs from roughly $1,200 to $3,500 depending on flue length and liner type. These are estimates for typical jobs; the written estimate sets the final price.
A few things move the number: how high the chimney sits above the roof, whether the roof pitch makes access slow, how much damaged brick has to come out, and whether the flue needs a liner repair alongside the masonry work. The way to avoid overpaying is to get the diagnosis in writing and see the camera footage before you agree to anything, because the biggest cost mistake is paying for a rebuild when a HeatShield resurfacing would have solved the problem. Our estimate is free, and it includes the inspection, the camera scan, and a clear breakdown of what’s included.
Chimney Repair Near Rhawnhurst – Our Service Area
We handle chimney repair across Rhawnhurst and the surrounding Northeast Philadelphia neighborhoods, including Holmesburg, Fox Chase, Bustleton, Oxford Circle, Tacony, and Torresdale. We also work with homeowners in Fort Washington, Mayfair, Cheltenham Village, and Rockledge, and response times are typically same-day or next-day depending on the schedule. Wherever you are in the area, one call covers the sweep, the repair, and any liner work from the same specialist.
Serving Rhawnhurst, PA – Our Local Coverage Area
We serve Rhawnhurst and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Repair in Rhawnhurst
Chimney repair covers any work that restores the structure or function of the chimney rather than just cleaning it, including repointing mortar, replacing spalling brick, waterproofing the masonry, fixing flashing, resurfacing or relining the flue, and rebuilding the stack when the damage runs deep. It also includes fireplace repair when the firebox or damper is part of the problem. We diagnose the whole system first so the repair solves the actual cause, not just the visible symptom. Call (866) 861-1187 to book an inspection and get a written estimate.
Most repointing, flashing, and waterproofing jobs are done in a single visit of a few hours. Spalling brick repair and liner work usually take a full day, and a rebuild can run several days depending on the height and extent of the damage. We give you a time estimate with the written quote so you know what to plan for. Call (866) 861-1187 for an exact timeline.
Small jobs like repointing or flashing repairs typically run $250 to $900, waterproofing is often $300 to $700, and liner-related flue repairs generally range from about $1,200 to $3,500. A full rebuild is priced per job after inspection. The written estimate sets the final price, and the inspection and estimate are free. Call (866) 861-1187 for an exact quote.
Yes. We install and service DuraFlex stainless liner systems and HeatShield ceramic resurfacing, along with Gelco and Olympia Chimney components for caps and dampers. If your chimney already has one of these systems, we inspect it and repair it to the same standard. Whether you have one of these or any other make, we can help. Call (866) 861-1187 to talk through your system.
Same-day appointments are often available for chimney repair in Rhawnhurst. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday, and we’re closed Saturday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (866) 861-1187 to schedule.
We back our repair work with a satisfaction guarantee. If something isn’t right after the job, you call us and we come back to make it right. Because we work exclusively in chimney and fireplace service, the repair is done by technicians who handle this work every day, not a generalist fitting it in between other jobs. Call (866) 861-1187 with any questions about your repair.
Clear the area around the fireplace and hearth, and make sure we can get to the roof and the cleanout without moving furniture. That’s most of it; you don’t need to do anything to the chimney itself. If you’ve noticed leaks, smoke smell, or staining, point them out when we arrive so we inspect that area closely. Call (866) 861-1187 to confirm your appointment.
Schedule Your Chimney Repair Service in Rhawnhurst Today
From a small repointing job to a full liner rebuild, one call covers it all, and the estimate is free. We diagnose before we quote, show you the evidence, and let you know when a repair can safely wait. Call (866) 861-1187. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Protect your home from the flue up.
Written by the team at Chimney Sweep Rhawnhurst.