Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Liner & Rebuild for Rhawnhurst Homeowners
A cracked or missing liner is the problem most Rhawnhurst homeowners don’t know they have until a sweep finds it. On the older rowhouses and twins around Castor Avenue and Rhawn Street, the original clay tile liners have usually been through decades of heating cycles, and many have gaps at the joints that let heat and carbon monoxide reach the wood framing. We solve that. Our technicians have up to 15 years of experience, we install DuraFlex and HeatShield systems, and chimney work is the only trade we handle. Call (866) 861-1187 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
What Our Chimney Liner & Rebuild Service Includes
Every job starts with camera inspection, so you see exactly what we see before anything is quoted. From there, the right fix might be a small liner repair or a full rebuild, and we’ll tell you plainly which one your chimney actually needs.
Stainless Steel Liner
A stainless steel liner is a new flue inside your old chimney, sized to the appliance so exhaust moves the way it should. You need one when the existing clay tiles are cracked, spalling, or the wrong size for a modern furnace or insert. We install DuraFlex stainless systems, and we measure the flue and the appliance before ordering anything, because an undersized liner is worse than no liner at all.
Flexible Liner
Flexible liners are the answer for chimneys with offsets, bends, or a flue that won’t take a rigid pipe. They’re common in the older Rhawnhurst housing stock, where the chimney path is rarely a straight shot from top to bottom. We use flexible DuraFlex liner where the flue geometry calls for it, and we pull it to full length so there are no hidden joints partway down.
Liner Replacement
Not every damaged liner needs a full tear-out. Replacing the liner means pulling the failed section and fitting new material that matches the appliance and the flue size. We recommend it when the surrounding masonry is still sound and the existing tiles can’t be salvaged; if the chimney structure itself is failing, we’ll say so and quote the bigger job instead.
Partial Rebuild
A partial rebuild addresses the section of chimney above the roofline, which takes the worst of the weather and often cracks first. You need one when the crown, the top courses of brick, or the mortar near the flue are failing but the chimney below is still solid. We rebuild that top section, reset the crown, and reflash where the chimney meets the roof so water stops finding its way in.
Full Chimney Rebuild
A full rebuild is for chimneys where the masonry has lost structural integrity from the ground up, which usually means water has been getting in for years. This is the job most sweep-only companies turn away, and it’s the reason our liner and rebuild capability matters. We take the chimney down to a sound base, rebuild with new brick and mortar, and line the new flue before we call it finished.
Liner Repair
Liner repair covers the middle ground: hairline cracks, isolated gaps, and worn spots that don’t justify replacement yet. We use HeatShield ceramic resurfacing to seal and restore the inside of a liner that’s still structurally sound, which can extend its life without demolition. If a repair will only buy you a year, we’ll tell you that too, and quote the replacement honestly.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Liner & Rebuild
We install and work with DuraFlex and HeatShield, plus Gelco and Olympia Chimney, which are the material brands certified chimney professionals specify nationwide. That matters on a loose flue: DuraFlex flexible liner is built for the bends and offsets in older Philadelphia chimneys, and we know how it behaves when it’s pulled through a tight offset. HeatShield ceramic resurfacing is a different tool entirely, used when the liner is worn but not gone.
Gelco and Olympia Chimney components round out the lineup on caps, tops, and the fittings that hold a liner in place. Whether you have one of those brands or any other make, we can help. We don’t guess at what’s inside your flue; we inspect it first and recommend the material that fits the job, not the one we have the most of.
Signs You Need Chimney Liner & Rebuild Right Now
- Crumbling or missing clay tiles. A camera sweep often shows flaking tile and gaps at the joints, which lets heat and exhaust reach the framing. That’s a liner problem, and it doesn’t fix itself.
- White staining on the chimney exterior. That chalky residue is a sign of moisture moving through failing mortar and brick. Left alone, it works its way into the liner and the structure behind it.
- A smoky fireplace that used to draw well. A liner that’s cracked or the wrong size for the firebox will push smoke back into the room. It’s one of the clearest signs of a liner that needs attention.
- Visible cracks or spalling above the roofline. This is where a partial rebuild usually starts. Catching it early keeps the repair to the top section instead of the whole chimney.
- Loose pieces of masonry in the firebox or on the roof. Falling brick or mortar means the chimney is shedding material from the inside out. That’s a structural question, not a cleaning one, and it needs a look before the next fire.
Our Chimney Liner & Rebuild Process – Step by Step
- 1
Camera inspection of the full flue. We run a video camera from the top of the chimney down to the smoke chamber, so the condition of the liner is documented, not guessed. You see the footage with us.
- 2
Written scope and a flat price. You get a written estimate for the work with the materials and scope spelled out, and the price is set per job by that estimate. Nothing starts until you agree to it.
- 3
Protection and prep. We cover the floor and the work area, set up access to the roof, and stage the materials so the job runs in one pass. On a rebuild, we assess the brick and mortar at this stage to confirm the scope.
- 4
The liner or rebuild work. We install the new stainless or flexible liner, or rebuild the masonry section, then reseal the crown and check the flashing. Every joint and termination is inspected before the job is closed out.
- 5
Final inspection with photos. We run the camera again after the work and show you the result. The photo report is included, and the local pro we connect you with is licensed and insured as their state requires.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Liner & Rebuild Cost in Rhawnhurst?
Most liner jobs in Rhawnhurst run in the range of a few thousand dollars, with a full rebuild costing more, but the number depends entirely on your flue. A straightforward stainless liner replacement is on the lower end; a rebuild above the roofline with new brick, crown, and flashing sits at the higher end. A typical liner replacement with inspection and photo report runs roughly $1,800 – $4,500 depending on flue length and appliance type.
A partial rebuild typically runs $2,000 – $6,000, and a full chimney rebuild can run $8,000 – $20,000 or more depending on height and the condition of the masonry below the roofline. Those are estimates, not quotes. The written estimate sets the final price, and we give it to you before any work begins.
What moves the number: the length of the flue, whether the existing tiles come out cleanly, the appliance (wood, gas, or a furnace flue), and whether the crown or flashing needs rebuilding at the same time. On a rowhouse, roof access and working height can add labor.
How to avoid overpaying: ask for camera evidence before anyone recommends a full rebuild. A liner repair with HeatShield may solve a smaller problem for a fraction of the replacement cost, and if the work can safely wait a season, we’ll tell you so. Our estimate is free and includes the photo report, so you can see the flue yourself before you commit.
Chimney Liner & Rebuild Near Rhawnhurst – Our Service Area
We handle chimney sweep Rhawnhurst and chimney liner & rebuild work throughout the neighborhood and into the surrounding areas: Fox Chase, Bustleton, Mayfair, Holmesburg, Oxford Circle, Tacony, Torresdale, Rockledge, Cheltenham Village, and Northeast Philadelphia. We also cover chimney liner & rebuild in Fort Washington and chimney liner & rebuild in Mayfair. Most appointments in and around Rhawnhurst are booked into the next opening, and we answer 24/7 with fast dispatch from 7am to 7pm, Sunday through Friday.
Serving Rhawnhurst, PA – Our Local Coverage Area
We serve Rhawnhurst and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Liner & Rebuild in Rhawnhurst
A chimney liner is the flue inside your chimney that carries smoke and exhaust safely up and out of the house. A rebuild becomes necessary when the masonry itself, not just the liner, has failed and can’t be repaired. On Rhawnhurst’s older homes, years of freeze-thaw and water intrusion often make a partial rebuild the honest fix. Call (866) 861-1187 for an inspection and a free estimate.
A stainless or flexible liner install usually takes a day, while a partial rebuild typically runs two to three days depending on weather and access. A full rebuild takes longer. The timeline is spelled out in your written estimate. Call (866) 861-1187 to schedule an inspection.
A liner replacement typically runs about $1,800 – $4,500, a partial rebuild $2,000 – $6,000, and a full rebuild $8,000 – $20,000 or more. The exact figure depends on flue length, appliance type, and how much of the masonry has failed. The written estimate sets the final price, and the inspection with photo report is free. Call (866) 861-1187 for an exact quote.
Yes. We install and work with DuraFlex and HeatShield, along with Gelco and Olympia Chimney, and we know where each one tends to wear. Whether you have one of those brands or another make, we can help. Call (866) 861-1187 to talk through what you have.
Same-day service is often possible when the schedule allows, and we answer 24/7 on the phone. Dispatch runs 7am to 7pm, Sunday through Friday, and we’re closed Saturday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (866) 861-1187 to reserve a slot.
Material and workmanship coverage depends on the brand and the scope, and it’s written into your estimate before work starts. We’ll walk you through the terms on the specific DuraFlex or HeatShield system being installed. Ask for the warranty in writing with the quote. Call (866) 861-1187 for details.
Clear access to the fireplace and the hearth, and move anything breakable away from the work area. Tell us about any gas appliance or insert connected to the chimney, since that changes how we inspect and sweep. We protect floors and furnishings once we’re on site. Call (866) 861-1187 if you’re unsure what to move.
Schedule Your Chimney Liner & Rebuild Service in Rhawnhurst Today
A liner is the part of your chimney that protects the house, and it’s the part most people never see. Our technicians have up to 15 years of experience, the inspection and photo report are included, and the estimate is free with no obligation. Call (866) 861-1187. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Rhawnhurst.